Interplater hd85 thermal pdf. Thermal analysis and design enae d principles of space systems design u n i v e r s i t y o f maryland nonideal radiative. Service Manual + 68/85 Plate Processor InterPlater 85/ HD Polymer Service manual Plate Processor+ 68/85 .. Cleaning of developer heating element. Thermal Plate Processor Raptor 85/ Interplater HD 85 G&J used/refurbished. Glunz Jensen Interplater Plate Processor Model Perfect Condition.
|Published (Last):||17 July 2017|
|PDF File Size:||4.48 Mb|
|ePub File Size:||8.22 Mb|
|Price:||Free* [*Free Regsitration Required]|
Be careful to hold on to the exit guide when removing the screws.
If replenish and therma containers are installed as described earlier the processor will be ready for automatic fill-up when switched on. Use plenty of water, a soft brush and a soft cloth to clean the gab between the heating element and the tank bottom.
How to read pdf files in my mobile
Alternatively a forklift truck is recommended. If straight position B is wanted please follow the description for B. Filling up will start upon confirmation. Cleaning of spray tubes Developer section Clean the spray tubes in the developer section with hot water to remove potential blocking of the holes. X3,F to F10,1 Black: Nslam book sms for friends Kosher organic ranchero season 2 download free Basketball coaching philosophy pdf files Gubcsi lajos ex libris bookshelf The contest problem book ix pdf to jpg Beer ware software license types marvel movie lineup Sa college pretoria fees booklet Odishon download legendado film Kick ass 2 free movie Chris brown bunkin download Roswell season 1 direct download.
The electrical diagrams are located in Appendix A.
Interplater hd85 135 thermal pdf
The boxes need to be removed from the pallet before lifting up the processor from the pallet. Provide for additional cable protection, e. The installation procedure is described later in this manual.
If the machine has low level by starting up, or goes low level during production, note on the display will ask to fill up. Delivered with the processor is a tool tbermal installation of brush rollers. This is done when installation of the processor has been completed.
A-8 Sensors and control devices. Cleaning agents Never use cleaning agents containing chlorinated solvents, acetic or phosphoric acid. The processor has been either off or in sleep mode for more than 72 hours. CE Interpllater of Conformity 4 Language: It must therefore be connected to earth to avoid electrical shocks. See the packing list s delivered with the equipment for further information. The fuses are placed on the fuse PCB behind the cover.
Off replenishment The replenishment system also features an “off replenishment” function which adds an amount of developer into the developer bath when the processor is turned on after being off for a long period. Design of thermal interface material with high thermal. These constitute a health hazard and could damage the processor.
If using automatic circuit breakers, make sure they are Type D. B9″ to gum replenishment container 2.
Product data sheet thermal h 11 bath fluid thermal h julabo thermal bath fluids are ideally suited for all of your temperature control applications and guarantee safe and reliable operation. A-6 V AC control devices. X3,D to F10,1 Blue: Mount the spray tubes 4.
For normal cleaning purposes and to rinse after using other cleaning agents. Characteristics of thermal interface materials 4 apparent thermal conductivity it is a common practice to calculate an apparent or effective thermal conductivity from 1355 single measurement of thermal impedance z at one thickness t of a particular interface material.
Procedure of adjustment See illustration on the yhermal page. When performing any service, maintenance, calibration, or trouble shooting etc. Installation kit Installation- and spareparts kits are included with the processor. Problems with the processor b. Rewire if necessary accordingly to table below.
The gum section contains one roller pair 18 and a smaller roller 19 situated close to the upper roller. The processor sections are described in detail on the following pages.
When the machine is started up for the first time after have stayed off interplster more than 72 hours the alarm appears: Hd855, depending on the local water quality, it may be necessary to use a drill bit to clean the holes and remove sediments mechanically.
For cleaning of rollers, guides, tank walls, and all surfaces, especially the exit table and the feed table if fitted. The rollers 9 ensure that the plate is transported correctly underneath the brushes 10 and the rollers 11 make sure of proper contact between brushes and plate. For cleaning and maintenance subjects see the processor user manual. End of life Estimated product life: Preparations See the illustration on the following page. If the machine has low level by starting up, or goes low level during production, the pump will start automatically filling up to level.
Install the interplxter standing on the left side of the processor. Trouble shooting General If the processor does not work properly, refer to the following pages to find the paragraph that comes closest to your problem. Processor must interpkater off when set to “0”. Spare parts and service period: Before operating the processor you may need to perform a 1135 to match your local supply voltage. The thermal impedance of the tim was measured using a new.