Introduction The XL-2T is a state of the art microprocessor-based control/ communicator. The system features seven (7) fully programmable zones. Programming. XL-2T. Security System. Installation and Setup Guide. STAY. INSTANT. ACYLB. READY APPENDIX D – SYSTEM PROGRAMMING WORKSHEET. Example: To program phone number enter 1#8#0#0# etc. Exit Program STAY. Default Panel Short “EEPROM RESET” pins on panel and power up system.

Author: Vudor Mezira
Country: Thailand
Language: English (Spanish)
Genre: Science
Published (Last): 27 July 2008
Pages: 447
PDF File Size: 5.12 Mb
ePub File Size: 4.20 Mb
ISBN: 507-7-55360-470-4
Downloads: 36817
Price: Free* [*Free Regsitration Required]
Uploader: Gogal

Fire Trouble is reported to the CS if enabled program question 32, location 3. See the following diagram: For UL installations see wiring diagram for hookup. With this device some systems can obtain dial tone in areas which do not automatically provide dial tone. Keypad Sounder Section 5 – System Operations Fbk Sounder The sounder or loudspeaker housed inside the keypad, emits annunciates sounds according to the condition of the security system.

By pressing ‘print’ button you will print only current page. We regret any inconvenience this may have caused and appreciate your continued support fbu FBII products. Programming Questions This topic defines the programming questions and the values for each question. Upon entry to the system log view, LCD based keypads will show the events one at a time starting from the oldest event.

Quick Arming allows arming the system without entry of a user code and will report as user Enter the digit from the table below. Don’t show me this message again.


FBI XL-2 Program Sheet

The system contains up to fifteen user codes 4 digits each with the following applications: Don’t have an account? The following is a quick comparison. For Built-in Siren Driver, connect a single 8 ohm speaker only. Page 70 Section 6 – System Programming When programming the English zone descriptors, use the following techniques to program the characters: Programming can be performed through any of the compatible keypads or the system can be uploaded and downloaded remotely using the EZ-Mate PC Downloader Software.

I shall be pleased to learn from you in this regard. To print the manual completely, please, download it.

The alarm was then activated, without me activating it. Some new features have been added and others have been modified. Section 5 – System Operations 4.

Page of 93 Go. Directly to a single or double gang electrical junction box.

Comments to this Manuals Your Name. Page 40 Section 5 – System Operations If a user code is not required to set the time, then enter: How can i change or get rid of this 3 digit code.

On LED keypads the sounder will beep after each entry. For Bell Output, connect a profram driver ex: The purpose of this manual is to give you a brief overview of the XL-2T control panel, and provide instructions for installing a basic system.

To select a trigger type enter the 2 digits in either L1 L2 or L3 L4 desired trigger type for each output trigger.


The keypad sounder annunciates differently to indicate the following conditions: I then pressed code button followed by master codethen user no 3 and then new 4 digit user code. If a keypad tamper code progeam entered then it will be transmitted to the Central Station.

This enables Fire and Burg zones to report restores. It is time to change code for security reasons. The porgram features seven 7 fully programmable zones.

FBII XL-2T Installation And Setup Manual

The FCC requires the following statement for your information. Section 5 – System Operations Keypad Sounder The sounder or loudspeaker housed inside the keypad, emits annunciates sounds according to the condition of the security system. When the switch is pushed toward the front of the keypad, in the opposite direction of the arrowthe switch is in the OFF position. This will be used by the CS downloading computer to determine the proper account information to download to this subscriber.

Next, enter programm desired account number each digit followed by the key. The auto arm time represents dl2t time of day that the area will automatically arm if it is not already armed.