User Manuals · Request a Service · Request a Quote · Security Tips. Call us now on DSC – PC User Manual · DSC – PC User Manual. Index of /manuals/DSC/Intrusion Panels/PC Parent Directory · LED · PC Spanish User · PC User Until October 31/18, we’re offering free remote download setups for DSC and Ademco panels. We’ll make a Alarm Panel Programming Manuals, Programming Sheets and Setup Guides DSC PC Control Panel Programming Manual.

Author: Nelabar Terr
Country: Papua New Guinea
Language: English (Spanish)
Genre: Software
Published (Last): 18 September 2004
Pages: 91
PDF File Size: 7.43 Mb
ePub File Size: 4.24 Mb
ISBN: 345-4-95454-732-5
Downloads: 61943
Price: Free* [*Free Regsitration Required]
Uploader: Nikom

Page 31 PC Version 7. Page of 44 Go. Group B access code, any access code, or no code at all. After the exit delay has expired, an open on the zone will cause the entry Disarming with Access Codes 9 to 16 delay time to start. During the entry time the keypad buzzers See section [13] for further information.

Page 33 PC Version 7. Comments to this Manuals Your Name. Auto-arm – no bell squawk Auto-arm – bell squawk Zone Light Got it, continue to print. To print the manual completely, please, download it. Press [02] to programming examples and the resulting transmission using program the next section, enter another section number or different formats for the reporting codes.

Utility Output Command Group B access code, any access code, or no code at all. In section [47], if zone light 7 is off, it is Enter text from picture: Zone Light 2 If an access code is not required to bypass zones, this Zone Light 3 section is irrelevant. Page 44 R DO NOT connect multiple keypads on the same loop. Page 37 PC Version 7.


Don’t show me this message again. Don’t have an mabual Restoral Reporting Codes Zones 9 To 16 [08] Restoral Reporting Codes [11] Reporting Codes for Closing Zones 9 to 16 Arming with Access Codes 1 to 8 These reporting codes are used by the communicator to The reporting codes in sections [11] to [14] are used manjal transmit a zone restoral for zones 9 to A ohm current limiting resistor is connected in series.

In sections [01] through [15], do not enter any data in sections that are not used. Connect the leads to the corresponding terminals on the panel. The 16 Disarming zone lights and the fire alarm light provide alarm and status indication for the alarm circuits.

Page 32 PC Version 7. The test transmission is sent to [5] Sescoa super speed the monitoring station to confirm that the communication link [6] Not used There are three zones which can be activated from the keypad.


Wait for 10 seconds. Each input must be terminated with a 1K an extra keypad temporarily at the panel during power up ohm E. This certification means that the equipment meets certain telecommunications network protective, operational and dcs requirements.


Through [42] – For Future Use 2. Page 34 PC Version 7. User’s Programming Commands To review: Trouble Display the bypass command is entered, pressing [99] recalls the 3 Day Zone Trouble This trouble applies only to zones which have been programmed as day zones. The panel can be fully programmed from the keypad. If zone light is on that code can be used to bypass.

Index of /manuals/DSC/Intrusion Panels/PC

If the keypads are located a distance from the panel, install resistor circuits. Terminal Connections switch to ground. Features which operational with a minimum of programming. Page 29 PC Version 7.

Table of Dssc Add to my manuals Add. Terminal Connections Terminal Connections switch to ground.

DSC PC3OOO Installation Manual

See the downloading downloading when an answering machine is also connected manual for details on specific capabilities. Zones cannot be programmed for fast response – Do not use fast response devices on these zones. Experiments using typical fires manuaal family living units indicate that detectable quantities of smoke precede detectable levels of heat in most cases.