DESIGNJET T1300 SERVICE MANUAL PDF

Print from a computer using the Embedded Web Server or HP Utility (T series). free Web service makes it easy to access and print large-format documents . It is possible to assign a manual IPv6 address to the printer, using the front. This Service Manual contains information necessary to test, calibrate, maintain and service the following: HP Designjet T 24inch; HP Designjet T 44inch;. HP DesignJet T and T Printer Series. Using your The only warranties for HP products and services are set .. Web Services manual configuration.

Author: Kagagis Kajigrel
Country: Angola
Language: English (Spanish)
Genre: Finance
Published (Last): 14 September 2009
Pages: 143
PDF File Size: 1.89 Mb
ePub File Size: 2.63 Mb
ISBN: 702-9-64338-144-2
Downloads: 48938
Price: Free* [*Free Regsitration Required]
Uploader: Fenririsar

Page 73 System Error: Lower the handle to rest on the carriage cover. Q Basket Tube T Disconnect and remove the following cables indicated from the Primer of the Service Deslgnjet.

Lift the Top Cover of the printer sufficiently to gain access to the Touch Control Panel ribbon cable. Starwheel Assembly Removal Switch off the product and remove the power cable.

The Carriage Assembly moves to the left and stops in the correct position to remove the printheads. Unscrew four T screws as shown.

HP DESIGNJET T1300 ePrinter series Service Manual

Cleaning the Glass Plate The customer is recommended to clean the glass plate periodically, depending on the usage of the product. Choose a different product. Disconnect and remove the following cables indicated from the Intermediate PCA. Page The product will display the current time and the new time.

DESIGNJET T/T ePrinter series & T eMFP series Service manual

Open the ferrite and remove from the cable this action is required to be able to pass the harness under the arc. Installation The correct adjustment of the cable of the Scanner Position Sensor is important, if the cable is not adjusted correctly this could cause the cable to disconnect when the scanner is opened, or become trapped between covers.

  LA LEYENDA DE JIRAIYA EL GALANTE PDF

Center Covers Front 3 of 3 on page Unscrew the freewheel assembly. Press OK to finish. Page 92 Diagnostic tests also need to be performed after removing or replacing certain product components. If scanner calibration result is FAIL then: Scan-axis Motor Removal Switch off the product and remove the power cable. Pull both Data and Power Harness under the left arc On the other side of the unit, detach Power and Data cables from cable ties.

HP DesignJet T1300 44-in Printer User Guides

Disconnect the Pinchwheel Lifter Sensor, and unroute the cable. If the amount of memory that the product needs to process the file is more than the amount available, the product will display this system warning. Once you have completed the Rewinder diagnostic test, you must perform a Paper Advance Calibration.

This product has been exchanged for a new or refurbished product. The PRS subsystem is designed to move the carriage assembly between two predetermined vertical positions with respect to the plane of the print platen. Measure the total length of the two vertical rules at both sides of the copied plot we call it M1 and M2. Scan Axis Motor SV. Remove the Touch Control Panel cable from the cable tie.

  LIVING GREYHAWK MODULES PDF

Remove the Torsion Damper from a clip on the side. Q Integrated Front Trim Left.

Ink Setup failure Corrective action: The product makes some further checks. Belt Assembly on page In some cases, particularly after resetting the product to factory defaults, it may take as long as 5 minutes to obtain an IP configuration. Lift up the Front Top Cover by adjusting the trims. Delete any non-standard paper preset in the product both the ones that have been created by the user and the ones that have been installed as OMES profiles through the EWS or the HP product Utility.

Emergency firmware upgrade with USB flash drive on page 74 Download again the firmware file from the source, as the original may be corrupted.

Lift attachment clamp vertically to release it from the Platen. Home screen dynamic icons The following items are displayed only on the home screen. Scanner Parts 3 of 3 on page Remove the Front Cover on page This product was sold by a reseller. USB flash drive are supported. Remove the Media Output Assembly on page The product performs a series of movements numbered from 1 to Shut down the product and replace the drop detector.

Click the file once to select it, then right-click and select Save target as.