The switches by Omron are all designated D2F, from there it gets a bit .. Atm I have a mice on my desk which uses two D2FC-F-7N(10M) for. Buy OMRON D2FC-F-7N(10M) Micro Switch Microswitch for Mouse with fast shipping and top-rated customer you know, you Newegg!. Those little switches have a snap fit cover, and can be opened up. Omron switch catch. carefully pull on the catch with a fine blade, and remove.

Author: Grogal Nejinn
Country: Guyana
Language: English (Spanish)
Genre: Life
Published (Last): 4 September 2006
Pages: 308
PDF File Size: 7.3 Mb
ePub File Size: 2.57 Mb
ISBN: 898-6-60814-664-8
Downloads: 58716
Price: Free* [*Free Regsitration Required]
Uploader: Groktilar

Needless to say this is not usable so it’s repair or replace time. Thanks for your help!

Definitive Omron Switch Guide for Mice

Omron switches are the common by far used in mice, however the naming scheme and rumors abound about what each does and is. Thanks for the info Before I went shopping thought it might be a good idea to check the switches in my CM Inferno are compatible.

Frankly, you do not want any of these on your switch, as they pertain to the soldering terminals and different ways to actuate the omrob, almost none of which are useful to use.

Elrick Hype Master Posts: This is important if you play FPS and need to rapid fire. How do I fix an Omron d2fc-f-7n microswitch from unwanted clicks? This is backed up by the D2fc-d-7n ROG Spatha mouse which uses a machine numbers on the switches inside the mouse, but retail naming on the two switches included this mouse ommron the user to change them.

Alin – Yes, this site even mentions a switch with a ms!

Sun, 24 July Youtube has a video: Whereabouts do you live? Unplug the mouse now. That’s a smart makeshift decision.

Better to err on the side of caution. Bill the Lizard 4 Another points is the “Machine switch Numbers”. Is the manufacturer not debouncing with an SR latch? Whereas many other mouse housings do not.


Your mouse may have some slop to prevent this when your fingers are off the mouse, omfon as soon as you put them on it, the lifespan is probably starting to drop as the weight of your fingers remove that slop.

By using our site, you acknowledge that you have read and understand our Cookie PolicyPrivacy Policyand our Terms of Service. Perhaps a friend has a broken one? Tear off a thin 5mm wide strip of J-Cloth or similar. D2F vs D2FC indicates origin and more.

In our situation, it doesn’t matter much and given time and corrosion tarnishthe gold will maintain it’s level of resistance better. Levers can be removed, so if you want a specific d2fcc-f-7n in a hurry and can only find it with a lever, you can always remove it from the switch and use it without problems, just be careful removing it. The obvious solution is to remove the malfunctioning microswitch and replace with a spare, but where I live they aren’t available at all.

It was time to fix my mouse again, and this time around I didn’t have enough unused switches d2fc-d-7n last time I used sensor sensitivity buttons as donors in the mouse to replace the bad ones.

Sat, 30 April I thought that most of them are interchangeable, aren’t they? If your mouse has Chinese models, the Japanese models may not fit unless there is a teeny bit of slop between button and switch itself, which is common. Design-wise, these match the Japanese switches, however, without a micrometer it’s impossible to eyeball, so you will need to just install and try them, if they are super sensitive, then it needs Chinese switches rather than Japanese.

A quick Google search turned up nothing. Therefore it behaves less like a spring, and more like a lever. Anything touching that button shortens the lifespan. X2fc-f-7n this point, plug in the mouse and d2fc-f-7b the switch. Or does the switch really bounce so hard that it bounces between both contacts when pressed?


Recently got some huano switches. Leslieann on Wed, 01 February As you start pounding the button d2fc–f-7n rapid fire, you can easily exceed the -F’s force limits which is only a little over a pound. If it still doesn’t work, then get a new switch. This does work but in the case of a high-use mouse expect to do this once every x2fc-f-7n or so.

d2fc-v-7n However they often coincided with the button color or a painted dot on top. This took hours to compile, reading websites, pdf’s and more, it contains all you should need to know.

Omron D2FC-F-7N

You might find it easier to remove the spring from the switch first. Just remember if you don’t like it and try to go back to the Japanese version things will be very sloppy. While d2fc-ff-7n at first runs counter to Omron, if you remember when I said resting your finger on the button shortens the lifespan, it’s possible that the 20Ms are more easily damaged.

If not, try to push on it in such a way that the problem happens. I need to replace the switches on a couple of mice, but is there one in particular that’s more quiet? That’s a chinese D2F-J01F: Besides it’s a solution, not a question.

And the switches are brand new.

Advanced search bounce or buckle? You can find these switches now under Qiaoh name: