ASTM D4417 PDF

For hot-dip galvanizing applications, it is possible to measure and verify the steel surface profile according to ASTM D, Standard Test. ASTM D – 11 Standard Test Methods for Field Measurement of Surface Profile of Blast – Download as PDF File .pdf), Text File .txt) or read. ASME B, Surface Texture (Surface Roughness, Waviness and Lay); ASTM D, Standard Test Methods for Measurement of Surface Profile of Blast.

Author: Fausar Faukinos
Country: Togo
Language: English (Spanish)
Genre: Science
Published (Last): 18 May 2004
Pages: 164
PDF File Size: 2.11 Mb
ePub File Size: 18.15 Mb
ISBN: 135-1-15059-307-3
Downloads: 28819
Price: Free* [*Free Regsitration Required]
Uploader: Akinokazahn

These changes reflect industry research on current tooling which revealed averaged measurements are consistently less than the values obtained using replica tape. This is done because of evidence that coatings performance in any one small area is primarily in?

Peak density the number of peaks per unit area also plays a key role in maintaining adhesion of the coating system and provides greater resistance to corrosion undercutting when the coating system gets damaged while in service. During abrasive blast cleaning, the mass of the abrasive and the velocity of the abrasive movement created by compressed air generates kinetic energy the abrasive can reach speeds of over miles per hour as it exits the blast nozzle.

The values given in parentheses are for information only. This method can be used to measure the surface profile depth that is created by abrasive blast cleaning or impact-type power tools.

Larger repair areas or prepared hot-dip galvanized surfaces for painting can atsm measured with two readings taken from a minimum of three, 6×6 inch 15×15 cm areas.

Your comments will receive careful consideration at a meeting of the responsible technical committee,1which you may attend Copyright? Therefore, differences are inevitable, particularly with deeper surface profiles, and the results may or may not fall within the specified range for one of the two methods. Surface profile is defined as a measurement of the maximum peak-to-valley depth created by abrasive impingement against a surface during abrasive blast cleaning operations, or by an impact-type power tool.

  KARUNASENA JAYALATH PDF

For hot-dip galvanizing applications, it is possible to measure and verify the steel surface profile according to ASTM D, Standard Test Methods for Field Measurement of Surface Profile of Blast Cleaned Steel, prior to application of repair materials where the surface has been prepared via power tool astn abrasive blast cleaning methods.

The instruments described are readily portable and sufficiently sturdy for 4d417 in the? The information provided herein is not intended as a representation or warranty on the part of the AGA.

Updates to ASTM D | American Galvanizer’s Association

Only the use of surface profile depth micrometers and replica tape were updated, and the specification changes are as follows: The base of the instrument rests on the tops astk the peaks of the surface pro?

For more information related to surface preparation as it relates to hot-dip galvanized steel, you can contact AGA Corrosion Engineer Alana Hochstein at ahochstein galvanizeit.

Once the burnishing process is complete, the replica tape is removed from the surface and the image is measured using a spring-loaded micrometer. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. Leave a Reply Cancel reply Your email address will not be published. Measure the thickness of the tape compressed foam and asmt plastic?

Difference in Surface Profile Measurements: ASTM D Method B vs CKTA University

Your comments will receive careful consideration at a meeting of the responsible ast, committee,1which you may attend. The mode is determined with the comparator of Test Method A. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm.

  INTRODUCTION TO PHENOMENOLOGY DERMOT MORAN PDF

The creation of this peak-valley pattern in the surface effectively increases the surface area, providing an anchor for the coating system. By continuing to use our site, you accept our use of cookies To learn more, click Read More to view our Privacy and Cookies Policy. Do not drag the instrument aztm the surface between readings, or the spring-loaded tip may become rounded leading to false readings.

The height of a single valley below a plane at the level of the highest surrounding peaks is measured with the? There are d417 techniques suitable for laboratory use not covered by these test methods. Your email address will not be published. Leave this field empty.

Replica Tape – Although the technology has remained mostly constant for replica tape since its introduction, industry research has addressed the sufficient number of readings required to achieve an accurate measurement. It is the responsibility of whoever uses this standard to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Adjust the instrument to zero.

Updates to ASTM D4417

Historical Version s – view previous versions of standard. Link to Active This d44117 will always route to the current Active version of the standard.

The surface profile must be compatible with the coating system. This includes personalizing content and advertising. For measurements that fall between tape sizes, it is still required that two readings using each tape are to be averaged to comprise one reading i.